---

07.2 Carburetor (Solex), Fuel Pump, Throttle Linkage - M110

Carburetor, idle speed control, regulation of engine

• 07.2-090 - Layout and function of Solex carburetor 4 A 1
  • Select page... A. General B. Float C. Idle speed D. Bypass carburetor stage I E. Acceleration F. Main jet system carburetor stage I G. Bypass carburetor stage II H. Main jet system carburetor stage II I. Starting device (choke) J. Vacuum governor K. Fuel return valve
• 07.2-092.1 - Technical modifications (revisions) of model years
  • Select page... A. (J) model year 1976 - Differences as compared with standard version B. (S) model year 1976 - Differences as compared with standard version C. (USA) model year 1973 - Differences as compared with standard version
• 07.2-092.2 - Technical modifications (revisions) of model years (cont'd)
  • Select page... D. (USA) model year 1974 Federal - Differences as compared with model year 1973 Federal E. (USA) model year 1974 California - Differences as compared with model year 1973 Federal F. (USA) model year 1975 - Differences as compared with model year 1974 Federal G. (USA) model year 1976 - Differences as compared with model year 1975

Idle speed control

• 07.2-100 - Adjusting idle speed
• 07.2-101 - Synchronizing idle speed systems
• 07.2-102 - Checking idle speed shutoff valves for function
• 07.2-104 - Removal and installation of idle speed shutoff valves

Regulation of engine

• 07.2-110 - Regulation of engine

Starting device (choke)

• 07.2-125 - Adjusting choke
• 07.2-128 - Testing starting device (choke) for function (cold start)
• 07.2-130 - Testing and adjusting TN choke for function
• 07.2-132 - Adjusting choke rod
• 07.2-134 - Testing pulldown diaphragm for leaks
• 07.2-138 - Removal and installation of TN choke
• 07.2-140 - Removal and installation of choke
• 07.2-142 - Checking and correcting choke housing mark
• 07.2-145 - Checking choke cover-stepped heater
• 07.2-147 - Subsequent installation of choke cover-stepped heater

Accelerating system

• 07.2-150 - Adjusting accelerating pump
• 07.2-152 - Checking suction valve and delivery valves of accelerating pump for leaks
• 07.2-154 - Removal and installation of accelerating pump diaphragm
• 07.2-156 - Subsequent installation of vapor bubble draw-off for accelerating pump (USA 1975/76 only)

Carburetor stage II

• 07.2-170 - Checking and correcting air valve adjustment of stage II
• 07.2-172 - Checking and correcting jet needle adjustment of stage II
• 07.2-174 - Removal and installation of restoring spring for air valve of stage II
• 07.2-175 - Subsequent installation of modified adjusting pin for air valve preload of stage II
• 07.2-176 - Subsequent installation of bypass bores of stage II

Float

• 07.2-180 - Adjusting float level
• 07.2-182 - Checking float chamber external venting system
• 07.2-186 - Checking fuel return valve

Carburetor (total)

• 07.2-190 - Cleaning carburetor
• 07.2-192 - Removal and installation of carburetor cover
• 07.2-194 - Removal and installation of carburetor

Fuel pump

• 07.2-210 - Checking fuel pump
• 07.2-212 - Removal and installation of fuel pump

Regulation

• 07.2-300 - Adjustment of regulating linkage
• 07.2-310 - Removal and installation of engine longitudinal regulating shaft
• 07.2-320 - Removal and installation of front wall regulating shaft
• 07.2-330 - Removal and installation of accelerator pedal 

---

 

 

Copyright © 2003, 2004, 2005 Steve Nervig.
All Rights Reserved